rigacci.org

User Tools

Site Tools

Trace:
doc:appunti:net:adsl

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
doc:appunti:net:adsl [2012/05/25 12:03] – [Qualità del segnale] niccolodoc:appunti:net:adsl [2012/05/25 12:12] (current) – [Qualità del segnale] niccolo
Line 38: Line 38:
 ===== Qualità del segnale ===== ===== Qualità del segnale =====
  
-Il **SNR Margin in Downstream** (oppure Signal to Noise in DownStream o DS Margin in Downstream, a seconda dell'apparecchio). Se il valore di questa voce è **superiore a 12 dB**, la qualità della portante è buona o quantomeno sufficientemente stabile.+Due sono i parametri fondamentali:
  
-La voce **Line Attenuation in Downstream**: per una buona connessione il valore deve essere **inferiore ai 42dB**.+  - **SNR Margin in Downstream** (oppure Signal to Noise in DownStream o DS Margin in Downstream, a seconda dell'apparecchio). Se il valore di questa voce è **superiore a 12 dB**, la qualità della portante è buona o quantomeno sufficientemente stabile. 
 +  - **Line Attenuation in Downstream**: per una buona connessione il valore deve essere **inferiore ai 42dB**. 
 + 
 +Ecco una spiegazione più dettagliata presa da [[http://www.dslreports.com/faq/6728]]:
  
 ^ Relative Capacity Occupation  | Percentage of your overall available bandwidth used to obtain your service ATM rate. For example; if your max line synch rate was 5888Kbps and you were provisioned on a 1472Kbps service you would be using 25% capacity. 1472/5888=25% capacity. The lower the relative capacity the better, but you can still get maximum speeds (although a less stable connection) even with a very high relative capacity. In other words you could be synching at 1472Kbps with 98% relative capacity and achieve maximum speeds, but you may experience more disconnects.  | ^ Relative Capacity Occupation  | Percentage of your overall available bandwidth used to obtain your service ATM rate. For example; if your max line synch rate was 5888Kbps and you were provisioned on a 1472Kbps service you would be using 25% capacity. 1472/5888=25% capacity. The lower the relative capacity the better, but you can still get maximum speeds (although a less stable connection) even with a very high relative capacity. In other words you could be synching at 1472Kbps with 98% relative capacity and achieve maximum speeds, but you may experience more disconnects.  |
 ^ Noise Margin (AKA Signal to Noise Ratio)  | Relative strength of the DSL signal to Noise ratio. 6dB is the lowest dB manufactures specify for modem to be able to synch. In some instances interleaving can help raise the noise margin to an acceptable level. The higher the number the better for this measurement.  | ^ Noise Margin (AKA Signal to Noise Ratio)  | Relative strength of the DSL signal to Noise ratio. 6dB is the lowest dB manufactures specify for modem to be able to synch. In some instances interleaving can help raise the noise margin to an acceptable level. The higher the number the better for this measurement.  |
-^ Line Attenuation  | Measure of how much the signal has degraded between the DSLAM and the modem. Maximum signal loss recommendation is usually about 60dB. The lower the dB the better for this measurement.  | 
 ^ Output Power  | How much power modem (upstream) or DSLAM (downstream) is using. Maximum recommended is about 15dB. The lower the power the better for this measurement. | ^ Output Power  | How much power modem (upstream) or DSLAM (downstream) is using. Maximum recommended is about 15dB. The lower the power the better for this measurement. |
 +^ Line Attenuation  | Measure of how much the signal has degraded between the DSLAM and the modem. Maximum signal loss recommendation is usually about 60dB. The lower the dB the better for this measurement.  |
 +
doc/appunti/net/adsl.1337940212.txt.gz · Last modified: 2012/05/25 12:03 by niccolo