doc:appunti:hardware:raspberrypi_car
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
doc:appunti:hardware:raspberrypi_car [2013/08/09 16:59] – niccolo | doc:appunti:hardware:raspberrypi_car [2019/02/01 17:04] (current) – niccolo | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Raspberry Pi Car Device ====== | ====== Raspberry Pi Car Device ====== | ||
- | Riferimenti | + | ===== Dongle USB Edimax in Mode Master (Access Point) ===== |
+ | |||
+ | Normalmente l' | ||
+ | |||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | |||
+ | Ci vuole una **versione custom di hostapd**, forse occorre anche un **modulo kernel custom**, a seconda del chip WiFi. Vedere le seguenti pagine: | ||
+ | |||
+ | * https:// | ||
+ | * https:// | ||
+ | * https:// | ||
+ | |||
+ | Pare che ci siano risultati diversi a seconda del chip (RTL8188CUS, | ||
+ | |||
+ | * **[[https:// | ||
+ | * **[[https:// | ||
+ | * **[[https:// | ||
+ | |||
+ | Altri riferimenti | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
- | |||
- | ===== Dongle USB Edimax ===== | ||
- | |||
- | Ci vuole una versione custom di hostpad.... | ||
===== wpa_supplicant ===== | ===== wpa_supplicant ===== | ||
Line 32: | Line 47: | ||
===== hostap ===== | ===== hostap ===== | ||
- | Si vuole che il Raspberry | + | Al bootstrap |
La modalità master si ottiene con il software **hostapd**, | La modalità master si ottiene con il software **hostapd**, | ||
Line 56: | Line 71: | ||
</ | </ | ||
- | Volendo avviare hostapd al bootstrap | + | Volendo avviare hostapd al bootstrap |
< | < | ||
- | DAEMON_CONF="/ | + | #DAEMON_CONF="/ |
</ | </ | ||
Line 82: | Line 97: | ||
ifup wlan0=master | ifup wlan0=master | ||
</ | </ | ||
+ | |||
+ | ===== wpa_supplicant o hostap, mapping automatico ===== | ||
+ | |||
+ | Si vuole un **sistema automatico** per decidere se attivare l' | ||
+ | |||
===== dnsmasq ===== | ===== dnsmasq ===== | ||
+ | ===== Alimentazione a batteria ===== | ||
+ | |||
+ | Si è provato ad alimentare il Raspberry con un **2200mAh Li-Ion Rechargeable Power Bank** [[http:// | ||
+ | |||
+ | Nelle nostre condizioni il Raspberry è rimasto in funzione per oltre 24 ore, ma **alla fine si è spento**, si suppone per scaricamento della batteria e quindi per alimentazione insufficiente. | ||
+ | |||
+ | Una soluzione migliore potrebbe essere quella di utilizzare un circuito specifico per la ricarica/ | ||
+ | |||
+ | Attenzione alle batterie litio-polimeri! Hanno una resistenza interna molto bassa e quindi sono a rischio di carica/ |
doc/appunti/hardware/raspberrypi_car.1376060380.txt.gz · Last modified: 2013/08/09 16:59 by niccolo