This is an old revision of the document!
|Internal Memory||32 Gb|
|CPU||Qualcomm Snapdragon 625 2.0GHz 8-core|
|Screen||5.5 Inches, 1920 x 1080|
|Connector||USB Type C|
|Audio jack||3.5 mm|
There are several recipes on the net on how to root this phone, many of them does not apply to my phone, may be because they are plain wrong, or may be because they apply to phones with firmware older than mine. The recipe I report here was applied with success on a Xiaomi Mi A1 purchased in October 2018. At the factory it has an Android Oreo 8.0.0, after the phone received an OTA update to Android Oreo 8.1.0 with Android security patch level October 5, 2018.
The process of rooting this phone can be broken down in some steps:
It seems that the process can be reverted leaving no tracks (the unlock step is the main concern for warranty, etc.). Unfortunately - at least in my case - the unlock procedure started also a factory reset, which means loosing all customization (installed apps. etc.) and user data.
For this procedure to work, we need two programs installed on our PC: adb and fastboot. They are command line tools from the Android SDK. Whenever we need to use adb or fastboot tools, we need to enable Developer options, enable USB debugging, connect the USB cable to the PC and tap “allow” on the phone pop-up. See below or search on the internet for a step-by-step guide.
In this process we used some binary files downloaded from the internet. Beware that we are downloading binary-compiled software that will run with root privileges on our phone! We have to trust the people which provide that, we cannot inspect the source code and there is not an easy step-by-step guide to compile from the sources by ourself. So we trusted the following internet pages (and people):
The official TWRP for Xiaomi Mi A1 page has only the bare TWRP Recovey image. We need an installer instead, because the recovery partition does not exist, the image must be embedded into the boot partition.
In order of appearance, we need:
Questa procedura necessaria ad ottenere i privilegi di root, non comporta modifiche irreversibili allo smartphone. Tuttavia quando viene eseguita comporta un factory reset, cioè il ripristino del telefono alle impostazioni di fabbrica con la perdita di tutte le personalizzazioni utente (app installate, configurazioni, ecc.).
La procedura di ripristino di fabbrica dura diversi minuti, alla fine viene avviata la procedura di prima accensione (configurazione account Google, ecc.). Le applicazioni scaricate in precedenza e le configurazioni utente vengono perse, rimane invece l'eventuale aggiornamento del sistema operativo (es. Android 8.1.0 scaricato in precedenza invece di Android 8.0.0 installato alla vendita).
The first step will be to change the boot partition to replace the stock Recovery program with a custom one; so it is advisable to backup it first. Many Android devices have a dedicated partition to store the Recovery program, in this device we have instead the A/B system updates machanism, introduced by Google with Android 7.0 Nougat. So we don't have a recovery partition, but we have boot_a and boot_b partitions.
To ensure that the device has the A/B system updates instead of the recovery partition, we use the following command into the adb shell:
adb shell tissot_sprout:/ find /dev -name 'by-name' 2> /dev/null /dev/block/platform/soc/7824900.sdhci/by-name cd /dev/block/platform/soc/7824900.sdhci/by-name ls -l ... lrwxrwxrwx 1 root root 21 1970-07-10 05:23 boot_a -> /dev/block/mmcblk0p22 lrwxrwxrwx 1 root root 21 1970-07-10 05:23 boot_b -> /dev/block/mmcblk0p23 ...
The meaning is: search into /dev/ for a directory named “by-name”, look for the names boot_a and boot_b and take note of the actual partition names. You can see also that the recovery name does not exists.
Now we need to boot into an environment where we have root privileges, otherwise we cannot read the entire partitions. This means booting into the Fastboot Mode bootloader and load and run the TWRP Recovery program.
Wait several seconds untill the Fastboot logo appers, then execute this command on the PC:
fastboot boot recovery-3.2.1-2-oreo.img
This will load the TWRP Recovery program on the phone (it just upload in RAM, does not write to flash) and boot from that. If the phone is not unlocked, the command will fail. The TWRP running on the phone will allow the adb program from the PC to access the system with root privileges, so we can finally backup the partitions on our PC:
adb pull /dev/block/mmcblk0p22 boot_a.img adb pull /dev/block/mmcblk0p23 boot_b.img
With the phone booted in standard system mode, upload the TWRP installer to the storage. As explained above, this phone has the A/B system partitions, so it is not possible to flash an image file to the Recovery partition (which does not exists), we need an installer which will modify the boot_a or boot_b partition (which one is active at the moment).
We upload also the Magisk program (the su binary stuff and the management app), which we will use later.
adb push Twrp-recoveryInstaller-3.2.1-2-oreo.zip /sdcard/Twrp-recoveryInstaller-3.2.1-2-oreo.zip adb push Magisk-v17.3.zip /sdcard/Magisk-v17.3.zip adb push MagiskManager-v6.0.1.apk /sdcard/MagiskManager-v6.0.1.apk
As seen above, we have to reboot in Fastboot Mode and load the TWRP Recovery from RAM (allow the required time to the phone to start into Fastboot):
adb reboot-bootloader fastboot boot recovery-3.2.1-2-oreo.img
Once that TWRP is started on the phone, swipe to allow writing to the partitions, then choose Install and browse to the Twrp-recoveryInstaller-3.2.1-2-oreo.zip archive.
After the installation, the procedure will ask us if we want to install the TWRP App. You can answer yes, but it is not strictly required, the TWRP Recovery is a stand-alone program, it runs when requested without an underlying Android system and it does not require any App. The TWRP App may be used to install or upgrade the TWRP Recovery and to backup the existing Recovery, but it seems that the current version (1.19) is not able to handle the A/B system updates mechanism, it searches for the recovery partition, which does not exist in Xiaomi Mi A1 Oreo 8.1.0. So it's best not to use it.
Beware of this:
adb reboot-bootloaderand switch again to Slot B.
When rooting an Android device we generally need the su binary program (the actual Unix tool used to switch from normal user to root), plus an app to manage superuser permissions granted (or denied) to other applications. Historically the most known app for this purpose was SuperSU by Chainfire, but something changed. Chainfire retired from SuperSU development in October 2017 and new protecting schemas were introduced by Google into Android, mainly SafetyNet and dm-verity. The new leading-edge app for su management appears to be Magisk.
The first step is to install the ZIP archive which provides the su binary, we already copied the Magisk-v17.3.zip file to the phone storag. Let's reboot into TWRP Recovery executing from the connected PC the following command:
adb reboot recovery
Alternatively we can power-off the phone, then power it on using the button combination VolumeUp + Power. From the TWRP main screen, choose Install and browse the filesystem to the Magisk-v17.3.zip file. After the install succeeded, reboot into normal system.
The su binary by itself is not sufficient to use root privileges, we need to install also the management app. Use the phone's file manager to find the MagiskManager-v6.0.1.apk and install it, granting the install unknown apps permission as requested. We have root permission, finally! Check via adb:
adb shell tissot_sprout:/ $ su tissot_sprout:/ # id uid=0 gid=0
When an app requires root privileges, the Magisk management app will show a pop-up on the phone, allowing to grant or deny the permission, so be sure that the phone is not in screen-locked mode.
Once in Recovery Menu, you can boot into the Fastboot Mode using the menu entry Reboot to bootloader. Otherwise you can execute the adb command on a PC when the phone is booted normally and connected via the USB cable (it is required to enable USB debugging on the phone and to authorize the PC on the phone pop-up, once connected):
adb reboot bootloader
adb devices List of devices attached 574524d99913 device
By keypress: VolumeDown + Power simultaneously for few seconds.
Using a connected PC and adb:
adb shell screencap -p /sdcard/screen.png adb pull /sdcard/screen.png
|/data/misc/wifi/softap.conf||Hotspot WiFi (Tethering) configuration.|
|/system/etc/mkshrc||Run commands for the ADB shell.|
|/mnt/expand/<id>||microSD mounting point.|
|/sdcard → /storage/emulated/0||User's space into the microSD.|
|/system/xbin||Preferred directory for BusyBox installation (binary and synlinks).|
Some app requires special settings to run properly, e.g. DAVdroid needs to sync contacts and calendar events in background and does not like battery optimization enforced by Xiaomi's Android. You can control this setting from here:
In April 2019 my phone still was running the following:
MagiskManager warns about the availability of Magisk v18.1, the operating system too warns about the availability of Nov 2018 Android System Update. Also MagiskManager can be upgraded to v7.1.1 (but don't upgrade it before upgrading Magisk, the app must follow exactly the su binary package contained in Magisk).
Write how to complete the upgrade!