User Tools

Site Tools



This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
doc:appunti:linux:audio:audio_recording [2019/04/22 22:39]
niccolo [Wireless UHF microphone]
doc:appunti:linux:audio:audio_recording [2019/05/22 15:51] (current)
niccolo [Electrical compatibility and hardware autodetection]
Line 159: Line 159:
 {{wireless-mic-receiver.jpg?direct&240|}} {{wireless-mic-receiver.jpg?direct&240|}}
-To connect the receiver to the Ugreen **USB audio adapter**, we built an adapter cable with a **male jack 3.5 mm TRS**. This is the pinout:+To connect the **UHF receiver** to the **Ugreen USB audio adapter**, we built an adapter cable with this pinout:
-Male Jack 3.5 mm TRS  ^ Signal             ^ Female 1/4" jack  ^ +1/4" TS female jack  ^ Signal         3.5 mm TRS male jack  ^ 
-| **Tip**               | Microphone signal  | **Tip**           +| **Tip**              | Microphone     | **Tip**               
-| **Ring**              | Not connected      |                   +|                      | Not connected  | **Ring**              | 
-| **Sleeve**            | Ground             | **Sleeve**        |+| **Sleeve**           | Ground         | **Sleeve**            |
-===== Wireless UHF microphone on Android =====+The **2.6 volt** current provided by the USB adapter on th **jack ring** will go nowhere (not connected). The **2.6 volt** current provided on the **jack tip** is probably not required by the UHF receiver, but **it should not harm**. **No infromation** is available about **microphone impedence** expected by the USB adapter, on the other hand no information is available about the **impedence of the mic interface** of the UHF receiver.
 +Despite all this empirical approach, the **voice registration is quite satisfying**!
 +====== Audio Recording With Android ======
 +Recording audio using an **external microphone** connected to an **Android device** can be a real nightmare. We tried the hard way using a Chinese, no-brand, **wireless UHF microphone**!
 +We can group the problems you can face in three main categories:
 +  * Physical connection
 +  * Electrical compatibility and hardware autodetection
 +  * Software capabilities and settings
 +===== Physical connection =====
 +Most Android devices have a **3.5 mm jack** accepting a **TRRS connector in CTIA standard** and every brand of mobile phones produces **headsets** with their own standard. The vast majority of solutions uses **electret microphones** requiring a **bias current**, but use **some combinations of impedence** to detect the insertion of the microphone and to **handle the headset button** (or buttons).
 +So, connecting an external microphone, can be as simple as making a cable that connects the **ring** and the **sleve** of the **CTIA connector** to (respectively) the **ground** and the **microphone line** of the microphone. The hard part is to guess, or empirically try, if the microphone **requires a bias current**, if the Android device is provinding such a current and if the microphone produces a sufficient **output level** (actually a voltage in the order of the millivolts) that can be used by the device.
 +===== Electrical compatibility and hardware autodetection =====
 +As stated above, the first problem is **powering the microphone** itself, because generally we will use an **electret** one. It is a **common practice** to provide the power on the same line of the microphone signal, so **requiring just two wires** for both power (from the device to the mic) and for signal (from the mic to the device). The power, also called //bias current//, is generally in the range of **2.5** to **5.0 volt**.
 +On a Xiaomi Mi A1 smartphone, which has a **TRRS 3.5 mm jack, CTIA standard**, we measured a bias current of **2.19 volt** between the microphone (sleeve) and the ground (ring).
 +Another parameter which should be considered is the **impedence** FIXME
 +===== Software capabilities and settings =====
 +FIXME Complete the article!
 +Wishing to connect the **UHF microphone** to an **Android smartphone**, we prepared an **adapter cable**. From 3.5 mm jack TRRS male to 1/4" jack TS female, with this pinout:
 +^ 1/4" TS female jack  ^ Signal         ^ 3.5 mm TRRS male jack (CTIA)  ^
 +|                      | Not connected  | **Tip**                       |
 +|                      | Not connected  | **Ring**                      |
 +| **Sleeve**           | Ground         | **Ring**                      |
 +| **Tip**              | Microphone     | **Sleeve**                    |
 +The smartphone **did not sensed the microphone**, there is not much documentation about it, but it seems that the **autodetection** of the microphone is **based upon the impedence** of the mic itself, if it is too low, it is not detected.
 ===== Web References ===== ===== Web References =====
Line 177: Line 215:
   * [[|External Mic on Galaxy Devices]]   * [[|External Mic on Galaxy Devices]]
   * [[|Android: Forcing external microphone (jack input 3.5mm) to stay on]]   * [[|Android: Forcing external microphone (jack input 3.5mm) to stay on]]
 +  * [[|App that turns off microphone AGC (Auto-Gain Control)?]]
 +  * [[|Difference between VOICE_COMMUNICATION and MIC in MediaRecorder.AudioSource]]
 +  * [[|What is the best audiosource setting for calls?]]
 +  * [[|App to force android to use external microphone when one is plugged in]]
doc/appunti/linux/audio/audio_recording.1555965592.txt.gz · Last modified: 2019/04/22 22:39 by niccolo