rigacci.org

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Blackview BV5300 Android Phone (rooting) ======

I purchased this phone from Amazon in August 2023 for about **113 €**, to use as [[..:android:osmand_on_motorbike|GPS satellite navigation system on the motorbike]].

{{.:bv5300:bv5300-back.jpg?direct&600|The Blackview BV5300}}

^ Model            | Blackview BV5300  |
^ Size             | 161.5 x 77.6 x 15 mm, weight 280 g  |
^ RAM              | 4.0 Gb   |
^ CPU              | MediaTek Helio A22 (MT6761) - ARM Cortex-A53 2.0 GHz, 4 core  |
^ GPU              | PowerVR GE8300  |
^ Internal Memory  | 32 Gb    |
^ Screen           | 6.1 inches, 720 x 1560, brightness 500 cd/m² typical  |
^ Battery          | Non replaceable 6580 mA  |
^ Connector        | USB C    |
^ Android version  | 12       |
^ A/B (Seamless) System Updates  | No\\ No //boot_a// or //boot_b// partitions\\ ''fastboot getvar current-slot'' returned //GetVar Variable Not found//  |
^ Anti-Rollback Protection  | No\\ ''fastboot getvar anti'' returned //GetVar Variable Not found//  |

{{.:bv5300:bv5300-front.jpg?direct&200|BV5300: Front view}}
{{.:bv5300:bv5300-bottom.jpg?direct&200|BV5300: Bottom}}
{{.:bv5300:bv5300-right.jpg?direct&200|BV5300: Rigth buttons}}
{{.:bv5300:bv5300-left.jpg?direct&200|BV5300: Left button}}

===== Getting the scatter file =====

A Scatter File is a .txt file which is used to describe **parts of flash memory** in an Android device which is running on a MediaTek’s MTK chipeset. Usually, such files are needed at the time of flashing firmware using tools like the **[[..:android:sp_flash_tool|SP Flash Tool]]**.

Generally you find the scatter file for your specific device included into the firmware archive, but for the BV5300 I did not find any official firmware to download, nor the simple scatter file. Using the following procedure I managed to create my ''MT6761_Android_scatter_BV5300.txt'' (download below).

=== Tools required (GNU/Linux or Wine) ===

  * **SP Flash Tool v5.2228 for Linux**: https://spflashtool.com/
  * **WwR MTK V2.51** for Windows (runs also in Wine): https://androidmtk.com/wwr-mtk-tool

=== Get the preloader and the GPT table from the smartphone ===

To create the scatter file you need to exctract two memory regions from the smartphone flash: the **preloader** and the **partition table**. You can use the SP Flash Tool to read them directly from the phone:

  * Using **SP_Flash_Tool_v5.2228_Linux**:
    * Run **flash_tool.sh** 
    * In the **Download** tab, **Scatter-loading File**: choose any scatter file you have on your hard disk (this step is required to unlock the Readback function below).
    * Click on the **Readback** tab and delete all the partitions defined by the scatter file you loaded.
    * Add **two regions** to be read-back:
      * Filename: **preloader.bin**
        * Region: EMMC_BOOT1
        * Start Address: 0x0
        * Length: 0x100000 (1 Mb, but 256 kb should suffice)
      * Filename: **pgpt.bin**
        * Region: EMMC_USER
        * Start Address: 0x0
        * Length: 0x8000
    * Click on the Readback button.
    * **Turn off** the phone and **connect it to the USB cable**; the read-back should start automatically.

=== Create the scatter file using the WwR MTK v2.51 tool ===

The WwR MTK (Working with Rom MediaTek) program can create the scatter file by reading the partition table and the preloader image extracted in the previous step. The program is for the Windows operating system, but it runs also under the GNU/Linux Wine environment:

  * Using **WwR MTK v2.51**:
    * Unpack the program archive and enter the ''WwR_MTK_v2.51'' directory. Execute **wine WwR_MTK_2.51.exe** (wait the 120 seconds pause or pay for the program).
    * Beside //The file to be used//, click **Select file** and open the **pgpt.bin** file. The Table of sections (Table chart of GPT) will be shown.
    * Right click on the Table of sections and select **Create scatter file** from the context menu (wait the pause).
    * The program requires to read the preloader image (the EMMC_BOOT1 region saved with SP Flash Tool); select the **preloader.bin** from the files.
    * Specify the CPU type: **MT6761**. The progam will prompt to save the scatter file as MT6761_Android_scatter.txt.
    * The program will launch the **notepad** editor to open the newly created scatter file.

This is the file that I obtained: **{{.:bv5300:mt6761_android_scatter_bv5300.txt|MT6761_Android_scatter_BV5300.txt}}**.

===== Rooting =====

If your phone has the build number **BV5300_EEA_TE105_V1.0_20230705V11**, you can download the following archive containing the already patched **boot.img** and **vbmeta.img** images. Obviously you must trust me that the images don't contain malware or alike. If you don't trust me, you have to execute all the steps by yourself: **{{.:bv5300:bv5300_eea_te105_v1.0_20230705v11_magisk-26.1-boot.zip|BV5300_EEA_TE105_V1.0_20230705V11_magisk-26.1-boot.zip}}**.

Whith the files contained into that archive you can directly jump to the last step of this guide: [[#flash_the_bootimg_and_the_vbmetaimg_custom_images|Flash the boot.img and the vbmeta.img custom images]].

The standard rooting procedure (see [[https://topjohnwu.github.io/Magisk/install.html|installing Magisk]]) failed; **patching the boot image** and **flashing** it back into the phone worked as expected, but **flashing the vbmeta image** with the ''%%--disable-verity%%'' and ''%%--disable-verification%%'' options did not work: the bootloader still checks the signature of the images and because the boot image is tampered, the phone enters a **bootloop**. The bootloop occurs also if you disable //verity// and //verification// into the original vbmeta image, keeping the original boot image.

The **bootloop** can be solved by:

  - Keep **VolumeUp** + **Power** keys pressed (do it at the begin of boot) to enter the //Select Boot Mode//.
  - Select the **FASTBOOT** mode.
  - Flash back the original **boot.img** and **vbmeta.img** images.

The rooting method that actually worked is resumed here:

  - Enable the **Developer options**.
  - **Unlock the bootloader** (does a factory reset).
  - Download (read-back) the **boot.img** and **vbmeta.img** images from the phone using **SP Flash Tool**.
  - Install **Magisk** into the phone and **patch** the **boot.img** file.
  - **Sign** the patched boot image with an RSA public/private key.
  - Create a **custom vbmeta image** where the the public key of the boot image is the one used in the previous step.
  - Flash the patched **boot.img** and custom **vbmeta.img** with the phone in **fastboot** mode.

==== Tools required ====

  * **adb** and **fastboot**\\ Command line utilities from the Android SDK, available for GNU/Linux as Debian packages.
  * **SP Flash Tool v5.2228 for Linux**\\ Graphical program to read-back and flash images from and to an Android device based on the MediaTek chipsets. Available in two versions: for the GNU/Linux and the Windows operating system.
  * **WwR MTK V2.51**\\ Graphical program to deal with MediaTek ROM (firmware) files. In this case it is used to parse the content of the partition table to create a //scatter file//. The program is for the Windows operating system, but it runs also under Wine and GNU/Linux.
  * **Magisk v26.1**\\ Android app to be installed into the device. It is used to patch the original boot image adding the **su** (superuser, to gain root privileges) program into the ramdisk. Then it is used also to manage the superuser requests made by other Android apps.
  * **avbtool** for Python 3\\ Command line tool from the Android SDK; it is used to work on Android Verified Boot images.
  * **testkey_rsa2048.pem**\\ 2048 bit RSA public/private key. You can use your own key, but it is common practice to use the test key included into the Android SDK.

=== Download ===

^ Tool  ^ Local download  ^ Official link  ^
^ SP Flash Tool  | {{.:android-tools:sp_flash_tool_v5.2228_linux.zip|SP_Flash_Tool_v5.2228_Linux.zip}}  | [[https://spflashtools.com/|spflashtools.com]]\\ **WARNINIG**: The site is not managed by MediaTek; other sites exist, but none seems to be the official one.  |
^ WwR MTK        | {{.:android-tools:wwr_mtk_v2.51.zip|WwR_MTK_v2.51.zip}}  | [[https://androiddatahost.com/ybd43]]\\ **WARNINIG**: It seems that it does not exist an offical site for WwR MTK; on the internet you can find many which have re-packaged the same archive, like this one: [[https://www.gsmfirmware.net/2020/07/wwr-mtk-tool.html|www.gsmfirmware.net]].  |
^ Magisk         | {{.:android-tools:magisk-v26.1.tar.gz|magisk-v26.1.tar.gz}} | [[https://github.com/topjohnwu/Magisk/releases/tag/v26.1|https://github.com/topjohnwu/]]  |
^ avbtool.py     | {{.:android-tools:avbtool.py.txt|avbtool.py}} | [[https://cs.android.com/android/platform/superproject/main/+/main:external/avb/avbtool.py|cs.android.com]]  |
^ testkey_rsa2048.pem  | {{.:android-tools:testkey_rsa2048.pem.txt|testkey_rsa2048.pem}}  | [[https://cs.android.com/android/platform/superproject/main/+/main:external/avb/test/data/testkey_rsa2048.pem|cs.android.com]]  |

==== Enable the Developer options ====

This is a standard procedure for the Android devices: go to **Settings** => **About phone** and tap 7 times on **Build number**. After that you will find a new menu item into //Settings// => //System// => **Developer options**.

Under //Developer options// enable the **USB debugging** item.

==== Unlock the bootloader ====

From //Settings// => //System// => //Developer options// enable the **OEM unlocking**. Then you must execute the actual unlocking from the phone fastboot mode.

**WARNING**: Unlocking the bootloader will cause a **factory reset** of the phone and the device enters the **[[https://www.hovatek.com/blog/your-device-has-been-unlocked-and-cant-be-trusted-what-does-this-mean/|Orange state]]**, i.e. the device at each bootstrap warns the user that it can't be trusted anymore because the boot code can be altered. The orange state cannot be reverted, it may be a problem if you want to have the phone serviced under warranty.

Attach the phone to the PC using the USB cable, tap **Allow** on the phone screen to permit the PC to control the phone via the **Android Debug Bridge**. Issue the following commands on the PC terminal:

<code>
adb reboot bootloader
</code>

Wait untill the phone enters the fastboot mode displaying the ''FASTBOOT'' prompt. Check that the device has the unlock ability and do the unlock:

<code>
fastboot flashing get_unlock_ability
    (bootloader) unlock_ability = 16777216
OKAY [  0.001s]
Finished. Total time: 0.001s
fastboot flashing unlock_critical
    (bootloader) Start unlock flow
OKAY [203.867s]
Finished. Total time: 203.867s
</code>

Now you can reboot the phone:

<code>
fastboot reboot
</code>

At bootstrap you will see the message about the **Orange state** and the phone does a factory reset. After the reset you need to **enable again the Developer options** and **USB debugging**.

**WARNING**: The Orange state cannot be reverted, you can try to re-flash the original images and re-lock the bootloader, but it is not guaranteed that the latter is possible.

==== Read the "boot" and "vbmeta" images from the phone ====

Execute the **SP Flash Tool** on your GNU/Linux PC (launch the ''flash_tool.sh'' script, you must have the permissions to access the ''/dev/ttyACM0'' device, usually granted to the ''dialout'' group) and load the {{.:bv5300:mt6761_android_scatter_bv5300.txt|scatter file of the Blackview BV5300}} using **Scatter-loading file** box.

Click the **Readback** tab: reading the info from the the scatter file you must add the data to read the **boot** and the **vbmeta** partitions:

^ partition_name: boot  ^^
| file_name            | boot.img     |
| physical_start_addr  | 0x1F800000   |
| partition_size       | 0x2000000    |
| region               | EMMC_USER    |
^ partition_name: vbmeta  ^^
| file_name            | vbmeta.img   |
| physical_start_addr  | 0x1F9200000  |
| partition_size       | 0xE00000     |
| region               | EMMC_USER    |

Once entered the data, click the **Read Back** button. Turn off the phone and connect the USB cable: the reading of the partitions should start automatically and the two files will be saved.

==== Install Magisk and patch the boot.img ====

Copy the file **Magisk-v26.1.apk** and **boot.img** to the smartphone storage using the **adb push** command. Then install the apk file (you must grant the //install unknown apps// permission to the Android file manager).

Launch the Magisk app on the phone and select //Magisk// => //Install// => **Select and Patch a File**: point the program to the **boot.img** file that you uploaded into the phone storage. After a little of work you should obtain a modified boot image saved into a file like ''/sdcard/Download/magisk_patched-26100_HlUfS.img''. The image should contain a modified ramdisk, which will provide the **su** command (superuser) when the Android system is running, but actually without modifying the **system** partition.

Download the patched boot.img to your PC using the **adb pull** command.

==== Sign the patched boot.img ====

The Blackview BV5300 is based on Android 12 and the [[https://android.googlesource.com/platform/external/avb/+/master/README.md|Android Verified Boot]] process cannot be disabled. So the patched **boot.img** must be signed with an **RSA public/private key** and the public part must be included into the **vbmeta.img** partition.

You need the **avbtool.py** tool (it is a Python 3 script, so you must have Python 3 installed); with that script you can get some info from the original boot.img:

<code bash>
python avbtool.py info_image --image 'boot.img'
</code>

The output will reveal the **partition image size** (33554432 bytes, which is exactly the size of the file) and that the public key **algorithm** is //SHA256_RSA2048//.

Then you need a 2048 bit RSA key; you can create your own, but it is common practice to use the one included into the Android SDK. Download the RSA key named **testkey_rsa2048.pem**.

With all this information, you can sign the file (actually add an hash footer inside the file). Beware that the file will be patched in-place, so make a backup copy before running the command:

<code bash>
cp 'magisk_patched-26100_HlUfS.img' 'magisk_patched-26100_HlUfS-signed.img'

python avbtool.py add_hash_footer \
    --image 'magisk_patched-26100_HlUfS-signed.img' \
    --partition_name 'boot' --partition_size '33554432' \
    --key 'testkey_rsa2048.pem' --algorithm 'SHA256_RSA2048'
</code>

==== Create and sign a custom vbmeta.img ====

Since Android Verified Boot in this device cannot be disabled, we need a properly crafted and signed **vbmeta.img** partition. Essentially the vbmeta partitions contains:

  * An header with the overall **signing hash**.
  * A **list of partition names** to be verified by the bootloader. Along with each name there is **the public key** to be used for the verification (where the private part was used for signing that partition).
  * The **public key** whose private part was used for signing the whole vbmeta partition.

For the overall signing of the vbmeta partition we will use the same **testkey_rsa2048** used to sign the boot partition; we need to extract the public part from it (all the keys to be used will be saved into a ''keys'' subdirectory):

<code bash>
python avbtool.py extract_public_key \
    --key 'testkey_rsa2048.pem' \
    --output 'keys/testkey_rsa2048_pub.bin'
</code>

**NOTICE**: All the public keys used here are saved into the **AvbRSAPublicKeyHeader** format, not the default PEM or DER formats used by openssl. This is a specific format for the Android Verified Boot process.

From **vbmeta.img** we need to **extract all the public keys of the partitions that were not altered** (i.e. all the partitions listed in it, except the **boot** one). Browsing the //vbmeta.img// file with an **hex editor** it is easy to spot each entry of the list; it is composed as follows:

  * An empty space made up of **64 zero bytes**.
  * The name of the partition, e.g. **vbmeta_system**.
  * A token of four bytes:  **%%0x00 0x00 0x08 0x00%%** (this should be the default token for a 2048 bit key).
  * The actual key in **AvbRSAPublicKeyHeader** format. A 2048 bit keys results into a **516 bytes** chunk.

The //vbmeta// partition of the Blackview BV5300 contains the signing information about the following partitions:

  * vbmeta_system
  * vbmeta_vendor
  * boot

With an hex editor we need to extrac only the keys for **vbmeta_system** and **vbmeta_vendor** including the initial 4 bytes token, thus creating two files of **520 bytes each**. That key files will be used to create the signed custom vbmeta image, in fact the //vbmeta_system// and //vbmeta_vendor// images are unaltered, so we re-use the same public keys. I used the Linux program **hexedit**: with F9 and the arrows it is possibile to select a bytes region, F7 to copy and Ctrl-Y to save the copied region into a new file.

So we have three key files: **keys/key_vbmeta_system.bin** and **keys/key_vbmeta_vendor.bin** extracted from the original //vbmeta// image and **keys/testkey_rsa2048_pub.bin** that we will use to sign the custom //boot// image.

For the final recipe we need some other piece of information; launch **avbtool.py** to get **info_image** from the original **vbmeta.img**:

<code bash>
python avbtool.py info_image --image 'vbmeta.img'
</code>

What we need is the **Flags** value and the **Rollback Index Location** for each of the listed partitions. With that information we can compose the final command to create the custom and signed //vbmeta// partition:

<code bash>
python avbtool.py make_vbmeta_image \
    --key 'testkey_rsa2048.pem' --algorithm 'SHA256_RSA2048' --flag 0 \
    --chain_partition 'vbmeta_system:2:keys/key_vbmeta_system.bin' \
    --chain_partition 'vbmeta_vendor:4:keys/key_vbmeta_vendor.bin' \
    --chain_partition 'boot:3:keys/testkey_rsa2048_pub.bin' \
    --padding_size '14680064' --output 'vbmeta-custom-sign.img'
</code>

You should be able to understand each parameter: the //flag// (zero in our case), each partition name is followed by its //Rollback Index Location// and the name of the file containing the public key used to sign it, the padding size is the overall size of the vbmeta.img file.

We used the same //Rollback Index Location// used in the original vbmeta image. In teory an unlocked bootloader should accept any rollback index, while a locked bootloader will refuse to boot from lower indexes to prevent the downgrade of the firmware.


==== Flash the boot.img and the vbmeta.img custom images ====

Finally we have two files to be flashed into the phone: **magisk_patched-26100_HlUfS-signed.img** and **vbmeta-sign-custom.img**. Reboot the phone in fastboot mode and run the following commands from the PC:

<code bash>
fastboot flash boot 'magisk_patched-26100_HlUfS-signed.img'
fastboot flash vbmeta 'vbmeta-sign-custom.img'
fastboot reboot
</code>

==== Final check ====

{{ .:bv5300:magisk-requires-additional-setup.png?220|Magisk Requires Additional Setup}}
To check if superuser privileges were enabled, I installed the [[https://f-droid.org/en/packages/com.termux/|Termux app]] from the F-Droid repository. Into the Termux terminal I launched the **su** program. A pop-up from the Magisk app asked if I want to grant superuser privileges to Termux; request to which I agreed.

When I start the Magisk app a warning appears, stating that Magisk **Requires Additional Setup**. I don't know what is required by the app, but I checked that the basic functions are working, so **I refused** that request. Some users on the net reported that **by accepting** that requests, the superuser installation **actually broke**.


===== Useful commands =====

The **adb** and **fastboot** tools are provided by Debian packages of the same name. They require that the //USB debugging// option is enabled into the smartphone. Here are some usage examples:

Copy a file from the PC to the smartphone storage:

<code>
adb push Magisk-v26.1.apk /sdcard/Download
adb push boot.img /sdcard/Download
</code>

Copy a file from the smartphone storage to the PC:

<code>
adb pull /sdcard/Download/magisk_patched-26100_HlUfS.img .
</code>

Reboot the phone from normal system into fastboot mode (The prompt ''%%=> FASTBOOT mode...%%'' appears on the phone screen):

<code>
adb reboot bootloader
</code>

In fastboot mode, flash the patched boot image:

<code>
fastboot flash boot magisk_patched-26100_aWX9D.img
</code>

In fastboot mode, flash the vbmeta image disabling dm-verity (causes a bootloop in the Blackview BV5300):

<code>
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
</code>

In fastboot mode, reboot the phone into normal system:

<code>
fastboot reboot
</code>

===== Web References =====

  * **[[https://forum.xda-developers.com/t/root-blackview-bv5300.4620399/|Root Blackview BV5300]]**
  * **[[https://androidmtk.com/wwr-mtk-tool|Download WWR MTK Tool for Windows]]**
  * **[[https://topjohnwu.github.io/Magisk/install.html|Magisk Installation]]**
  * **[[https://www.hovatek.com/forum/thread-32664.html|How to create a custom signed vbmeta.img for Unisoc using AVBtool]]**
    * **[[https://www.hovatek.com/forum/thread-32667.html|How to extract public keys from a vbmeta image]]**
    * **[[https://www.hovatek.com/forum/thread-32674.html|How to use AVBtool and a private key to sign a Unisoc (SPD) image]]**
  * **[[https://android.googlesource.com/platform/external/avb/+/master/README.md|Android Verified Boot 2.0]]**
  * **[[https://www.hovatek.com/forum/thread-32719.html|How to disable dm-verity or Android Verified Boot (AVB)]]**
  * **[[https://www.hovatek.com/forum/thread-31664.html|How to remove Orange, Yellow & Red state warnings on MTK]]**
  * **[[https://forum.xda-developers.com/t/editing-system-img-inside-super-img-and-flashing-our-modifications.4196625/|Editing system.img inside super.img and flashing our modifications | XDA Forums]]**