doc:appunti:hardware:raspberrypi_nas_remote_control
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
doc:appunti:hardware:raspberrypi_nas_remote_control [2021/04/12 18:29] – created niccolo | doc:appunti:hardware:raspberrypi_nas_remote_control [2021/04/24 19:59] (current) – [Working kernel versions] niccolo | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== |
- | The old model is identified by **lsusb** with this output line: | + | I have two SNES-Like gamepads, both are recognized by the Linux kernel Dragonrise module **hid_dr**. |
+ | |||
+ | {{.: | ||
+ | {{.: | ||
+ | |||
+ | They are different models: the old model is identified by **lsusb** with this output line: | ||
< | < | ||
Line 12: | Line 17: | ||
Bus 002 Device 004: ID 0079:0126 DragonRise Inc. | Bus 002 Device 004: ID 0079:0126 DragonRise Inc. | ||
</ | </ | ||
+ | |||
+ | To **pair** the gamepad with the USB receiver, first proceed by disconnecting the host USB dongle. Press the **Start**, **Select** and **Up** buttons simultaneously on the gamepad; the red LED starts flashing rapidly. During the next 10 seconds you have to insert the USB receiver into the host port, the pairing takes place automatically. | ||
+ | |||
+ | ===== Configuring the gamepad in Kodi ===== | ||
+ | |||
+ | You have to install the package | ||
+ | |||
+ | * **kodi-peripheral-joystick** | ||
+ | |||
+ | Other packages may be useful to debug and solve problems: | ||
+ | |||
+ | * **input-utils** - Contains the **lsinput** and **input-events** tools, used to view input events produced by the gamepad. | ||
+ | * **evtest** - Contains the **evtest** tool, used to monitor input events. | ||
+ | |||
+ | Install the **kodi-peripheral-joystick** package and restart **Kodi**, then go to **Settings** => **System settings** => **Input** => **Configure attached controller**. In this section you can choose the controller type: Kodi 17.6 has only the **generic** one, Kodi 18.7 has a **generic Kodi** and a specific **Super Nintento**. | ||
+ | |||
+ | Il is possible to configure each key, but default settings should be OK. | ||
+ | |||
+ | Custom configuration is saved into the directory **$HOME/ | ||
+ | |||
+ | The gamepad goes to stand-by after some time of non-use. To wake it up it is necessary to press the **start** button; the red LED turns on and the gamepad is working. | ||
+ | |||
+ | ===== Problem: non working left and right arrows ===== | ||
+ | |||
+ | Everything is working correctly with a **Raspberry Pi 3**, using RaspiOS based on **Debian 9.11 Stretch** and **Kodi 17.6**. There is instead a problem with a **Raspberry Pi 4**, using RaspiOS based on **Debian 10.8** and **Kodi 18.7**: the **Left** and **Right** arrow keys do not work. | ||
+ | |||
+ | Someone had the same problem using Retropie: **[[https:// | ||
+ | |||
+ | ==== Working kernel versions ==== | ||
+ | |||
+ | ^ System | ||
+ | | Raspberry Pi 3 | 4.19.66-v7+ | ||
+ | | Raspberry Pi 4 | 5.10.11-v7l+ | ||
+ | | PC amd64 Debian 10.8 | 4.9.189-3+deb9u2 | ||
+ | | PC amd64 Debian 10.8 | 4.19.67-2+deb10u2 | ||
+ | | PC amd64 Debian 10.8 | 4.19.98-1+deb10u1 | ||
+ | | PC amd64 Debian 10.8 | 4.19.160-2 | ||
+ | |||
+ | ===== Web References ===== | ||
+ | |||
+ | * **[[https:// | ||
+ | * **[[https:// | ||
doc/appunti/hardware/raspberrypi_nas_remote_control.1618244989.txt.gz · Last modified: 2021/04/12 18:29 by niccolo